You have no items to compare.
Hi, Dear! Welcome to our online store...
XS-AC AC Signal Isolation Converter
· 1 in 1 out, 2 in 2 out. AC signals such as 0~1A, 0~2A, 0~5A, 0~50V, 0~100V, 0~250V are converted to isolated 4~20mA output. Terminal supply or DIN rail power supply is available.
· The XS-AC AC signal isolating converter converts the rms value 0~5A AC current signal or the RMS value 0~250V AC voltage signal into a standard 4~20mA signal. Conversion fine ±0.05% FS, no conversion dead zone appears near the zero input signal.
· The current input signal does not have an input terminal. The current signal is connected to the internal converter through the side of the single-turn current transformer. The current transformer turns ratio is 1:800, and the actual input signal of the converter is 0~2.78mA. Does not generate high heat on the terminals.
· The voltage input signal enters the converter through the terminal block, and the input voltage loop is also limited to 0~2.78mA, so that the actual input signal of the converter is equal to the actual signal corresponding to the current input, and the same conversion can be easily used without switching. Device.
· This product requires a separate DC power supply. Power-input-output isolation.
Model / selection table:
Option |
Model and code |
Description |
Basic model |
XS-ACI |
AC Current Signal Isolation Converter |
XS-ACV |
AC Voltage Signal Isolation Converter |
|
Channel form |
11 |
1 in 1 out |
12 |
1 in 2 out |
|
Input signal |
-A |
0~1A AC (corresponding to the basic model DS-ACI) |
-B |
0~2A AC (corresponding to the basic model DS-ACI) |
|
-C |
0~5A AC (corresponding to the basic model DS-ACI) |
|
-Z |
Special order |
|
Output signal |
A |
4~20mA |
B |
0~20mA |
|
Z |
Special order |
|
Power supply voltage |
-V1 |
Power supply (terminal) 20~32VDC |
-V2 |
Power supply (rail) 20~32VDC (special power supply DIN rail required) |
|
Service Code |
-QC9A |
Product Service Code |
Selection example |
Technical data:
Size:
Width |
14.5mm |
Height |
102.6mm |
Height |
100mm |
Housing Material / Color |
PC (Polycarbonate) + PPT Material / Black Gray |
Protection level |
IP20 |
Environmental conditions:
Ambient temperature |
-20~+60℃ |
Ambient temperature (storage or operation) |
-40~+80℃ |
Ambient humidity (operation) |
5~95%RH (no condensation) |
Input:
AC current signal |
0~1A AC、0~2A AC、0~5A AC |
AC voltage signal |
0~50V AC、0~100V AC 、0~250V AC |
Output:
Current output |
4~20mA ; 0~20mA |
Maximum output current |
28mA |
Current output load |
0~300Ω |
Output ripple |
<40mV p-p |
Power supply:
Rated supply voltage |
24VDC |
Power supply voltage range |
20~32VDC |
Maximum current consumption |
<35mA (1 in 1 out); <65mA (1 in 2 out) |
General parameters:
Standard accuracy |
Typical values±0.5%FS |
Temperature drift |
<±1μA/10℃ |
Power-on or storage time drift |
±2μA (180days) |
Load change effect |
±2μA |
Response time |
<10ms |
Power-on stabilization time |
<1s |
Electrical isolation |
Input-output-power supply: 2500V AC RMS / 1 minute |
Protection parameters |
· Power-on shock protection, power-on slow start >20ms |
Electromagnetic compatibility (EMC) |
In accordance with IEC 61326-1 (GB/T 18268), IEC 61326-3-1 |
LED status indication |
Green LED (power indication) |
Mounting method |
Horizontal or vertical mounting, can be mounted on standard 35mm DIN rail (or dedicated busbar backplane powered DIN rail) |
Wiring parameters:
Rigid conductor cross section (min/max) |
0.5mm²/2.5mm² |
Flexible wire cross section (min/max) |
0.5mm²/2.5mm² |
Minimum wire cross section (AWG) |
24 |
Maximum wire cross section (AWG) |
14 |
Stripping length |
7mm |
Connection type |
M3 screw fastening connection |
Crew torque |
up to 0.6Nm |
Certification/standards:
CE certification |
Meet CE standards |
Product diagram / terminal wiring diagram: